The short version of Moisture sorption fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-05-13. Anything still debated is marked as such rather than presented as settled.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Storage stability depends on water content, oxygen exposure, and temperature. Lyophilized solids are hygroscopic and can absorb water if exposed to humid air. Vials are usually sealed under vacuum or inert gas with rubber stoppers and aluminum crimps. Storage temperatures range from room temperature to refrigerated or frozen conditions depending on the material. Stability studies track potency, moisture, and physical form over time. Accelerated conditions can reveal sensitivity but may not predict long-term behavior.
Analytical methods for lyophilized materials include X-ray diffraction for crystallinity, differential scanning calorimetry for thermal transitions, and scanning electron microscopy for pore morphology. Moisture sorption analysis shows how the cake responds to humidity. These methods help distinguish amorphous from crystalline states and detect phase changes. Open questions remain about how pore structure changes during long-term storage and how best to predict collapse under varied conditions. Comparisons across studies are complicated by differences in formulation, cycle, and storage history.
| Property | Value | Notes |
|---|---|---|
| Common synonym | Freeze-drying | Same dehydration operation |
| Typical vacuum | 10-100 Pa | Pressure during primary drying |
| Primary drying temperature | -40 to -10 °C | Below collapse temperature for many formulations |
| Cycle duration | 12-72 hours | Varies with load, container, and formulation |
| Key phase change | Sublimation | Solid ice to water vapor |
Freeze-drying is used for materials whose activity or structure depends on low temperature and low water content. Examples include certain biologics, diagnostic reagents, starter cultures, coffee, and porous inorganic precursors. The dried product forms a cake whose porosity aids rapid wetting and dissolution. Main drawbacks are high energy use, long cycle times, and sensitivity to formulation and equipment variation. Questions remain about how freezing rates and ice morphology affect batch uniformity, especially when moving from laboratory to production scale.
Lyophilization, also called freeze-drying, is a dehydration process in which a solvent, usually water, is frozen and then removed by sublimation under reduced pressure. The method preserves heat-sensitive materials that would degrade in conventional drying. Large-scale use grew during the mid-twentieth century for blood plasma and antibiotics, and it later expanded to vaccines, enzymes, foods, and advanced materials. The process produces a dry, porous solid that usually reconstitutes rapidly. It is distinct from simple evaporation because the solvent bypasses the liquid phase during primary removal.
The process generally proceeds in three stages: freezing, primary drying, and secondary drying. During freezing, controlled cooling converts water into ice and may also crystallize or vitrify solutes. In primary drying, the pressure is lowered below the triple point, and heat is supplied so ice sublimes directly to vapor. Secondary drying removes water that remains bound to the solid matrix, yielding a low final water content. Product temperature must stay below the collapse or glass transition temperature to maintain structure. Cycle design therefore balances shelf temperature, chamber pressure, and time.
Quality control also examines cake structure, color, and reconstitution behavior. A collapsed or shrunken cake can indicate a thermal excursion during drying. Analytical methods such as X-ray diffraction, differential scanning calorimetry, and near-infrared spectroscopy can detect crystallinity or moisture distribution. Regulatory expectations focus on validated assays and lot-to-lot consistency. Questions remain about how well accelerated stability tests predict long-term behavior for every formulation. Visual inspection remains common but is subjective without trained reviewers and reference images.
After lyophilization, a product's quality depends on residual moisture, cake appearance, and reconstitution time. Residual moisture is often measured by Karl Fischer titration or thermogravimetric analysis. A low moisture content can slow chemical degradation, but overly dry cakes may be brittle or slow to dissolve. Stability studies track these attributes over months under defined temperature and humidity conditions. Batch records link these measurements to specific process runs and help identify trends before a product fails specification.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
=== Beyond Meat === In July 2018, A&W locations began serving Beyond Meat's vegan Beyond Burger. The chain had a shortage of the Beyond Burger in August 2018, but announced that all locations would receive stock by October 2018. In 2019 A&W expanded its Beyond Meat offerings with the release of the Beyond Meat Sausage N' Egger.
=== Analogues and derivatives === Analogues of 2C-B include 2C-I, 2C-C, DOB, 4C-B, 2C-B-FLY, and 25B-NBOMe, among others. DOB and 4C-B are α-alkyl derivatives of 2C-B, specifically the amphetamine (α-methyl) and phenylisobutylamine (α-ethyl) derivatives, respectively. β-Substituted derivatives of 2C-B such as BOB (β-methoxy-2C-B), BOH-2C-B (β-hydroxy-2C-B), βk-2C-B (β-keto-2C-B), and β-methyl-2C-B (BMB) have been described. βk-2C-B shows dramatically reduced potency and efficacy as a serotonin 5-HT2A receptor agonist compared to 2C-B. A variety of N-substituted derivatives of 2C-B have been tested, including N-methyl-2C-B, N,N-dimethyl-2C-B, N-ethyl-2C-B, and N-benzyl-2C-B. Most simple alkyl derivatives were considerably less potent than 2C-B, with N-ethyl-2C-B for instance having a 40 times lower affinity for the serotonin 5-HT2A receptor. The N-benzyl derivative however was found to have higher affinity than 2C-B itself, with N-(4-bromobenzyl)-2C-B binding even more tightly. This initial research did not include functional assays of activity, but later led to the development of potent substituted N-benzyl derivatives such as 25B-NBOMe, and 25B-NBOH. Another N-substituted derivative, 2C-B-AN, is an N-benzylphenethylamine-like prodrug of 2C-B. 2C-DB (6-bromo-2C-B) is a ring-substituted derivative of 2C-B. TWEETIO derivatives of 2C-B, in which one or both of the methoxy groups of 2C-B are extended to ethoxy groups, exist as well, such as 2CB-2-EtO.
=== Marketed === Daridorexant (nemorexant; Quviviq) – dual OX1 and OX2 antagonist – approved for insomnia in January 2022, formerly under development for sleep apnea – half-life 8 hours Fazamorexant (Mengping) – dual OX1 and OX2 antagonist – approved for insomnia in China in May 2026 – half-life 2–4 hours Lemborexant (Dayvigo) – dual OX1 and OX2 antagonist – approved for insomnia in December 2019 and released June 1 2020, under development for circadian rhythm sleep disorders, chronic obstructive pulmonary disease, and sleep apnea – half-life 17–55 hours Suvorexant (Belsomra) – dual OX1 and OX2 antagonist – approved for insomnia in August 2014, under development for delirium – half-life 12 hours Vornorexant (Vorzzz) – dual OX1 and OX2 antagonist – approved for insomnia in Japan in August 2025 – half-life 1.5–3 hours
=== Biochemical === In size-exclusion chromatography, the residence time of a molecule is related to its volume, which is roughly proportional to its molecular weight. Residence times also affect the performance of continuous fermentors. Biofuel cells utilize the metabolic processes of anodophiles (electronegative bacteria) to convert chemical energy from organic matter into electricity. A biofuel cell mechanism consists of an anode and a cathode that are separated by an internal proton exchange membrane (PEM) and connected in an external circuit with an external load. Anodophiles grow on the anode and consume biodegradable organic molecules to produce electrons, protons, and carbon dioxide gas, and as the electrons travel through the circuit they feed the external load. The HRT for this application is the rate at which the feed molecules are passed through the anodic chamber. This can be quantified by dividing the volume of the anodic chamber by the rate at which the feed solution is passed into the chamber. The hydraulic residence time (HRT) affects the substrate loading rate of the microorganisms that the anodophiles consume, which affects the electrical output. Longer HRTs reduce substrate loading in the anodic chamber, which can lead to a reduced anodophile population and performance when there is a deficiency of nutrients.
Sources: en.wikipedia.org
== Scientific contributions == Meir Wilchek is known for his research in the field of biorecognition or affinity phenomenon, and its various application, e.g. for affinity chromatography, affinity labeling, affinity therapy, and the avidin-biotin system. The avidin-biotin complex is the highest affinity interaction in nature, and its utilization to biochemistry integrates all of the former approaches. Other contributions include conversion of serines to cysteines, and was the first to prove experimentally the equation of Forster on dependence of energy transfer on distance, an approach known today as FRET. He also studied the fine structure of these chromophores using circular dichroism. More recently, he participated in a research team who studied how garlic works at the molecular level, thanks to a unique biotechnological procedure for producing large quantities of pure allicin, garlic's main biologically active component.
== Limitations and means of improvement == The main disadvantage of absorption spectrometry (AS) as well as laser absorption spectrometry (LAS) in general is that it relies on a measurement of a small change of a signal on top of a large background. Any noise introduced by the light source or the optical system will deteriorate the detectability of the technique. The sensitivity of direct absorption techniques is therefore often limited to an absorbance of ~10−3, far away from the shot noise level, which for single pass direct AS (DAS) is in the 10−7 – 10−8 range. Since this is insufficient for many types of applications, AS is seldom used in its simplest mode of operation. There are basically two ways to improve on the situation; one is to reduce the noise in the signal, the other is to increase the absorption. The former can be achieved by the use of a modulation technique, whereas the latter can be obtained by placing the gas inside a cavity in which the light passes through the sample several times, thus increasing the interaction length. If the technique is applied to trace species detection, it is also possible to enhance the signal by performing detection at wavelengths where the transitions have larger line strengths, e.g. using fundamental vibrational bands or electronic transitions.
Medical syringes include disposable and safety syringes, injection pens, needleless injectors, insulin pumps, and specialty needles. Hypodermic syringes are used with hypodermic needles to inject liquid or gases into body tissues, or to remove from the body. Injecting of air into a blood vessel is hazardous, as it may cause an air embolism; preventing embolisms by removing air from the syringe is one of the reasons for the familiar image of holding a hypodermic syringe pointing upward, tapping it, and expelling a small amount of liquid before an injection into the bloodstream. The barrel of a syringe is made of plastic or glass, usually has graduated marks indicating the volume of fluid in the syringe, and is nearly always transparent. Glass syringes may be sterilized in an autoclave. Plastic syringes can be constructed as either two-part or three-part designs. A three-part syringe contains a plastic plunger/piston with a rubber tip to create a seal between the piston and the barrel, where a two-part syringe is manufactured to create a perfect fit between the plastic plunger and the barrel to create the seal without the need for a separate synthetic rubber piston. Two-part syringes have been traditionally used in European countries to prevent introduction of additional materials such as silicone oil needed for lubricating three-part plungers. Most modern medical syringes are plastic because they are cheap enough to dispose of after being used only once, reducing the risk of spreading blood-borne diseases.
Other proteins bind to the ends of actin filaments, stabilizing them. These are called "capping proteins" and include CapZ and tropomodulin. CapZ binds the (+) end of a filament, preventing further addition or loss of actin from that end. Tropomodulin binds to a filament's (−) end, again preventing addition or loss of molecule's at that end. Tropomodulin is typically found in cells that require extremely stable actin filaments, such as those in muscle and red blood cells. These actin binding proteins are typically regulated by various cellular signals to control actin assembly dynamics in different cellular locations. Formins, for example, are typically folded in an inactive conformation until they're activated by the binding of the small GTPase Rho. Actin branching at the cell membrane is important for cell movement, and so the plasma membrane lipid PIP2 activates the nucleation promoting factor WASp and inhibits CapZ. WASp is also activated by the small GTPase Cdc42, while another nucleation promoting factor WAVE is activated by the GTPase Rac1.
==== Protease inhibitors ==== Some viruses include an enzyme known as a protease that cuts viral protein chains apart so they can be assembled into their final configuration. HIV includes a protease, and so considerable research has been performed to find "protease inhibitors" to attack HIV at that phase of its life cycle. Protease inhibitors became available in the 1990s and have proven effective, though they can have unusual side effects, for example causing fat to build up in unusual places. Improved protease inhibitors are now in development. Protease inhibitors have also been seen in nature. A protease inhibitor was isolated from the shiitake mushroom (Lentinus edodes). The presence of this may explain the Shiitake mushrooms' noted antiviral activity in vitro.
Sources: en.wikipedia.org
=== Pseudomonas syringae pv. tomato strain DC3000, its derivatives, and its tomato host === As its name suggests, P. syringae pv. tomato DC3000 (Pst DC3000) is virulent to tomato (Solanum lycopersicum). However, the tomato cultivar Rio Grande-PtoR (RG-PtoR), harboring the resistance gene Pto, recognizes key effectors secreted by Pst DC3000, making it resistant to the bacteria. Studying the interactions between the Pto-expressing tomato lines and Pst DC3000 and its pathovars is a powerful system for understanding plant-microbe interactions. Like other plants, the tomato has a two-tier pathogen defense system. The first and more universal line of plant defense, pattern-triggered immunity (PTI), is activated when plant pattern recognition receptors (PRRs) on the cell surface bind to pathogen-associated molecular patterns (PAMPs). The other branch of plant immunity, effector-triggered immunity (ETI), is triggered when intracellular (Nucleotide-binding site, Leucine-rich repeat) NB-LRR proteins bind to an effector, a molecule specific to a particular pathogen. ETI is generally more severe than PTI, and when a threshold of defense activation is reached, it can trigger a hypersensitive response (HR), which is purposeful death of host tissue to prevent the spread of infection. Two key effectors secreted by Pst DC3000 are AvrPto and AvrPtoB, which initiate ETI by binding the Pto/Prf receptor complex in Pto-expressing tomato lines like RG-PtoR.
Hyaluronic acid is one of the most common materials used for injectable filler procedures due to its natural presence in vertebrates. Its inherent biocompatibility and biodegradability makes it particularly well suited for these applications, contributing to its widespread use in aesthetic and medical treatments. The chemical structure of hyaluronic acid is made up of repeating disaccharide units that consist of N-acetyl-D-glucosamine and D-glucuronic acid. Crosslinking Mechanisms in Injectable Fillers Crosslinking mechanisms determine the mechanical stability, degradation behavior, prolonged in vivo retention time, and in situ gelation properties of the injectable filler material. Hydrogels used as injectable fillers may be formed through physical (non-covalent) interactions or chemical (covalent) crosslinking, with chemical crosslinking generally providing greater stability and tunability. In collagen-based fillers, crosslinking methods such as glutaraldehyde treatment have been used to enhance integration, while synthetic fillers like poly(methyl methacrylate) rely on particulate scaffolds that induce fibrotic tissue formation rather than on degradable networks. Among chemical approaches, enzymatic crosslinking has gained prominence for its ability to proceed under physiological conditions without toxic catalysts or external stimuli such as ultraviolet light. Common enzymatic crosslinking mechanisms include horseradish peroxidase (HRP), tyrosinase, and transglutaminase.
== Contraindications == Benzodiazepines require special precaution if used in children and in alcohol- or other drug-dependent individuals. Particular care should be taken in pregnant or elderly people, people with substance use disorder history, particularly alcohol dependence, and people with comorbid psychiatric disorders. Alprazolam should be avoided or carefully monitored by medical professionals in individuals with myasthenia gravis, acute narrow-angle glaucoma, severe liver deficiencies such as cirrhosis, severe sleep apnea, pre-existing respiratory depression, marked neuromuscular respiratory, acute pulmonary insufficiency, chronic psychosis, hypersensitivity, allergy to alprazolam or other benzodiazepines, and borderline personality disorder, where it may induce suicidality and dyscontrol. Like all central nervous system depressants, alprazolam in larger-than-normal doses can cause significant deterioration in alertness and increase drowsiness, especially in those unaccustomed to the drug's effects.
Outrageous. It exacerbates inequality and social division—one of the main problems of the USA. It deprives vulnerable groups of access to health care. Life expectancy is already declining, and the health differences between rich and poor are enormous. This law exacerbates this. The nonpartisan Tax Foundation had mixed opinions of the bill, saying it made "some smart cuts", in particular praising the extension of the Tax Cuts and Jobs Act of 2017 which it argued would provide stability for households. It also expressed support for its impacts on counting international business income. It criticized the political nature of the bill, calling it filled with carve-outs and political gimmicks that increased the complexity of the tax code. It also criticized the bill's non-equal application of taxation on citizens. The Economist described the bill's policies and passage as an example of "America's creeping dysfunction", criticizing its impact on increasing the deficit and describing its tax cuts as "gimmicks". It also criticized Trump's handling of the economy more broadly, saying the bill "illustrates the long-term damage Mr Trump is doing to the foundations of America's economy" and describing its passage as exacerbating the effects of Trump's attacks on the Federal Reserve, defunding of scientific research, high tariff policy, and erosion to the rule of law. It described these cumulative effects as threatening America's economic stability and making it a riskier place to invest.
=== Malicious contributions on Wikipedia === In September 2011, Hari admitted that he had edited articles on Wikipedia about himself and journalists with whom he had had disputes. Using a sock puppet account under the name "David r from meth productions", he added false and defamatory claims to articles about journalists including Nick Cohen, Cristina Odone, Francis Wheen, Andrew Roberts, Niall Ferguson and Oliver Kamm, and edited the article about himself "to make him seem one of the essential writers of our times". In July 2011, Cohen wrote about the suspicious Wikipedia editing in The Spectator, prompting the New Statesman journalist David Allen Green to compile evidence that Hari used the identity "David Rose" to pretend to be an editor who was qualified in environmental science. This led to an investigation by the Wikipedia community and "David Rose" was blocked from Wikipedia. Hari published an apology in The Independent, admitting that he had been "David Rose" and writing: "I edited the entries of people I had clashed with in ways that were juvenile or malicious: I called one of them anti-Semitic and homophobic, and the other a drunk. I am mortified to have done this, because it breaches the most basic ethical rule: don't do to others what you don't want them to do to you. I apologise to the latter group unreservedly and totally."
Sources: en.wikipedia.org
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.
Sublimation requires the solvent to remain solid so vapor leaves without passing through a liquid phase. If the product melts, the porous structure can collapse and drying becomes uneven. Maintaining frozen conditions preserves the intended physical form.
No, freeze-drying is a dehydration method, not a sterilization step. It can reduce water activity and limit microbial growth during storage, but it does not reliably kill microbes or remove endotoxins. Sterility must come from separate validated processes.
Karl Fischer titration is a common method, using coulometric or volumetric detection. Thermogravimetric analysis can also measure weight loss on heating. Results depend on sample handling because the dried solid can absorb moisture quickly.